Evaluation of the Accuracy of Wood Drilling Resistance Measurement Method in Dendrochronological Studies
DOI:
https://doi.org/10.37482/0536-1036-2023-5-135-150Keywords:
annual layers of wood, dendrochronological studies, drilling resistance profile, optical method, thin drill bit, measurement accuracy, drilling resistance measurement method, ResistYXAbstract
One of the promising methods for determining physical and mechanical properties and structure of wood is the method based on the measurement of drilling resistance. Limitations of application of the method of measuring drilling resistance in dendrochronological studies are related to a number of factors that have a significant impact on the accuracy of determining the variation of physical and mechanical properties of wood within annual layers: the depth of drilling, its direction relative to the fibers, and the speed parameters of the drilling process. In order to assess the accuracy of measuring the radial growth of pine wood (Pinus sylvestris L.) with moisture content of 6–8 %, the ResistYX device and standard thin drill bits were used. On the basis of comparative analysis of radial wood growth determined by the optical method and the method of measuring resistance to drilling, it was found that in order to obtain accurate data on growth with a correlation coefficient greater than 0.7, it is recommended to measure no more than 17 annual layers on one sample, which corresponds to an average total width of annual layers of 36.6 mm. The influence of the main reasons for the decrease in the accuracy of radial growth determination by the drilling resistance measurement method was studied: geometrical parameters of the cutting part of a thin drill bit, deviation of the drilling direction from the specified one, impossibility of precise determination of the strictly radial drilling direction, wood flaws, as well as friction of the drill shank when the drilling depth increases. To increase the accuracy of the method of measuring drilling resistance in dendrochronological studies it is proposed to develop a method including the use of a special or newly developed tool for more accurate determination of the core and radial drilling of wood or round timber; to increase the rigidity of the thin drill bit; to provide the required fixation of the thin drill bit during its initial contact with wood and inside the device. Further studies in this direction will be associated with the assessment of measuring accuracy for the radial growth of coniferous wood by the feeding force for drill bit penetration.
Acknowledgements: The research was supported by the Ministry of Science and Higher Education of the Russian Federation (Grant № 075-15-2021-674/3) and Core Facility Centre «Ecology, biotechnologies and processes for obtaining environmentally friendly energy carriers» of the Volga State University of Technology, Yoshkar-Ola and by the Russian Science Foundation grant No. 22-79-00098, https://rscf.ru/project/22-79-00098/.
For citation: Chernov V.Yu., Sharapov E.S., Gaisin I.G. Evaluation of the Accuracy of Wood Drilling Resistance Measurement Method in Dendrochronological Studies. Lesnoy Zhurnal = Russian Forestry Journal, 2023, no. 5, pp. 135–150. (In Russ.). https://doi.org/10.37482/0536-1036-2023-5-135-150
Downloads
References
Алметов А.Н. Совершенствование конструкции бурава для извлечения кернов древесины из растущих деревьев различных пород: дис. … канд. техн. наук. Йошкар-Ола, 2001. 174 с. Almetov A.N. Improving the Design of a Drill for Extracting Wood Cores from Growing Trees of Various Species: Cand. Eng. Diss. Mari State Technical University. Yoshkar-Ola, 2001. 174 p. (In Russ.).
Демаков Ю.П., Нуреева Т.В. Групповая и индивидуальная изменчивость годичного прироста деревьев по высоте в культурах сосны Марийского Заволжья // Вестн. ПГТУ. Сер.: Лес. Экология. Природопользование. 2019. № 3(43). С. 25–45. Demakov J.P., Nureeva Т.V. Group and Individual Variability of Annual Tree Height Growth in Pine Plantations of Mari Transvolga Region. Volga State University of Technology Bulletin. Forest. Ecology. Nature Management, 2019, no. 3, iss. 43, pp. 25–45. (In Russ.). https://doi.org/10.25686/2306-2827.2019.3.25
Колесникова А.А. Исследование свойств древесины по кернам. Йошкар-Ола: МарГТУ, 2002. 178 с. Kolesnikova A.A. Research of Wood Properties by Increment Cores. Yoshkar-Ola, Mari State Technical University Publ., 2002. 178 p. (In Russ.).
Матвеев С.М., Румянцев Д.Е. Дендрохронология / ВГЛТУ. 2-е изд., перераб. и доп. Воронеж: ВГЛТА, 2013. 139 с. Matveev S.M., Rumyancev D.E. Dendrochronology: Voronezh, Voronezh State Academy of Forestry Engineering Publ. 2013. 139 p. (In Russ.).
Патент № 95128 U1 РФ, МПК G01N 3/40 (2006.01), G01N 33/46 (2006.01), B23B 41/00 (2006.01). Устройство для измерения сопротивления сверлению: № 2010106686/22: заявл. 24.02.2010: опубл. 10.06.2010 / Е.С. Шарапов, В.Ю. Чернов, Т.В. Бычкова. Sharapov E.S., Chernov V.Yu., Bychkova T.V. Device for Drilling Resistance Measurements. Pаtent RF, no. RU 95128, 2010. (In Russ.).
Патент № 2607064 C2 РФ, МПК G01N 3/40 (2006.01), G01N 33/46 (2006.01), B23B 49/00 (2006.01). Устройство для измерения сопротивления исследуемого материала сверлению: № 2014140884: заявл. 09.10.2014: опубл. 10.01.2017 / В.Ю. Чернов, Е.С. Шарапов, Е.В. Смирнова, О.А. Соловьева. Chernov V.Yu., Sharapov E.S., Smirnova E.V., Solovieva O.A. Device for Drilling Resistance Measurements. Patent RF, no. RU 2607064, 2017. (In Russ.).
Румянцев Д.Е. История и методология лесоводственной дендрохронологии: моногр. М.: МГУЛ, 2010. 109 с. Rumyantsev D.E. History and Methodology of Silvicultural Dendrochronology. Moscow, Moscow State Forest University Publ. 2010. 109 p. (In Russ.).
Свидетельство 2016662108 РФ о государственной регистрации программы для ЭВМ ResistVIEW, 1.0: № 2016619406: заявл. 06.09.2016: зарег. 31.10.2016 / Е.С. Шарапов, В.Ю. Чернов, Е.В. Смирнова; заявитель и правообладатель ФГБОУ ВО «ПГТУ». Sharapov E.S., Chernov V.Yu., Smirnova E.V. Certificate on State Registration of the Computer Program no. 2016662108 «ResistVIEW, 1.0», 2016. (In Russ.).
Чернов В.Ю., Шарапов Е.С., Торопов А.С. Определение плотности древесины методом измерения сопротивления сверлению: моногр. Йошкар-Ола: ПГТУ, 2019. 200 с. Chernov V.Yu., Sharapov E.S., Toropov A.S. Evaluation of Wood Density Using the Drilling Resistance Measurement Method. Yoshkar-Ola, Volga State University of Technology Publ. 2019. 200 p. (In Russ.).
Чернов В.Ю., Шарапов Е.С., Торопов А.С., Смирнова Е.В., Павлов Д.А. Точность определения плотности древесины методом измерения сопротивления сверлению // Актуальные проблемы и перспективы развития лесопромышленного комплекса: сб. науч. тр. III Междунар. науч.-техн. конф. КГТУ. Кострома: КГТУ, 2015. С. 42–45. Chernov V.Yu., Sharapov E.S., Toropov A.S., Smirnova E.V., Pavlov D.A. The Accuracy of Wood Density Evaluation by Drilling Resistance Measurements. Proceedings of the third International Conference “Current problems and prospects for the development of the timber industry”, Kostroma State Technological University. Kostroma, Russian Federation, 2015, pp. 42–45. (In Russ.).
Черных Н.Б. Дендрохронология и археология. М.: Nox, 1996. 212 с. Chernyh N.B. Dendrochronology and Archeology. Moscow, Nox Publ. 1996. 212 p. (In Russ.).
Шарапов Е.С. Совершенствование методов и средств квазинеразрушающего контроля физико-механических свойств древесины и древесных материалов: дис. ... д-ра техн. наук. Архангельск, 2019. 340 с. Sharapov E.S. Improvement of Methods and Tools for Quasinondestructive Evaluation of Physical and Mechanical Properties of Wood and Wood materials: Doc. Tech. Sci. Diss. Arkhangelsk, Northern (Arctic) Federal University, 2019. 340 p. (In Russ.).
Шарапов Е.С., Смирнова Е.В. Определение физико-механических свойств древесины методом измерения сопротивления сверлению // Вестн. ПГТУ. Сер.: Материалы. Конструкции. Технологии. 2019. № 4(12). С. 120–134. Sharapov E.S., Smirnova E.V. Evaluation of Physical and Mechanical Properties of Wood by the Drilling Resistance Measurement. Volga State University of Technology Bulletin. Materials. Constructions. Technologies, 2019, no. 4, iss. 12, pp. 120–134. (In Russ.). https://doi.org/10.25686/2542-114X.2019.4.120.
Шиятов С.Г., Ваганов Е.А., Кирдянов А.В., Круглов В.Б., Мазепа В.С., Наурзбаев М.М., Хантемиров Р.М. Методы дендрохронологии. Ч. 1. Основы дендрохронологии. Сбор и получение древесно-кольцевой информации. Красноярск: КрасГУ, 2000. 80 с. Shiyatov S.G., Vaganov E.A., Kirdyanov A.V., Kruglov V.B., Mazepa V.S., Naurzbaev M.M., Hantemirov R.M. Methods of Dendrochronology. Part 1. Fundamentals of Dendrochronology. Collecting and Obtaining Tree-ring Information. Krasnoyarsk, Krasnoyarsk State University Publ., 2000. 80 p. (In Russ.).
Chantre G., Rozenberg P. Can Drill Resistance Profiles (Resistograph) Lead to Within-profile and Within-ring Density Parameters in Douglas-fir Wood? Proceedings of CTIA – International Union of Forestry Research Organizations (IUFRO). International Wood Quality Workshop: Timber Management Toward Wood Quality and End-Product Value. Forintek Canada Corp., Sainte-Foy, Québec, Canada, 1997, pp. 41–47.
Guller B., Guller A., Kazaz G. Is Resistograph an Appropriate Tool for the Annual Ring Measurement of Pinus Brutia? Proceedings of the International Conference NDE Safety. Czech Republic, 2012, pp. 89–94.
Kraler А., Beikircher W., Zingerl Ph. Suitability of Drill Resistance Measurements for Dendrochronological Determination. World Conference on Timber Engineering, Strength and Serviceability – Etreme Events. Aucklande, New Zealand, 2012, vol. 2. 302 p.
Kraler А., Beikircher W., Zingerl Ph. Strength Determination of Aged Wood, From 1250AD to Present, with Nondestructive and Semidestructive Test Methods. World Conference on Timber Engineering, Strength and Serviceability – Etreme Events. Aucklande, New Zealand, 2012, vol. 2, 188 p.
Mattheck C., Bethge K., Albrecht W. How to Read the Results of Resistograph M. Arboricultural Journal: The International Journal of Urban Forestry, 1997, vol. 21, iss. 4, pp. 331–346. https://doi.org/10.1080/03071375.1997.9747179
Nutto L., Biechele T. Drilling Resistance Measurement and the Effect of Shaft Friction – Using Feed Force Information for Improving Decay Identification on Hard Tropical Wood. Gen. Tech. Rep. FPL – GTR – 239. Proceedings of the 19th International Nondestructive Testing and Evaluation of Wood Symposium. 22–25 September 2015, 2015, pp. 154–161.
Oliveira J.T.S., Wang X., Vidaurre G. Assessing Specific Gravity of Young Eucalyptus Plantation Trees Using a Resistance Drilling Technique. Holzforschung, 2017, vol. 71, iss. 2, pp. 137–145. https://doi.org/10.1515/hf-2016-0058
Orozco-Aguilar L., Nitschke C.R., Livesley S.J., Brack C., Johnstone D. Testing the Accuracy of Resistance Drilling to Assess Tree Growth Rate and the Relationship to Past Climatic Conditions. Urban Forestry & Urban Greening, 2018, vol. 36, pp. 1–12. https://doi.org/10.1016/j.ufug.2018.09.010
Pressler M.R. Der Forstliche Zuwachsbohrer [The forestry increment borer]. Tharander Jahrbuch. Arnoldische Buchhandlung, Leipzig. Dritte Abtheilung III, 1866, pp. 137–209. (In Germ).
Rinn F., Schweingruber F.H., Schar E. Resistograph and X-ray Density Charts of Wood Comparative Evaluation of Drill Resistance Profiles and X-ray Density Charts of Different Wood Species. Holzforschung, 1996, vol. 50, iss. 4, pp. 303–311. https://doi.org/10.1515/hfsg.1996.50.4.303
Rinn F. Resistographic Visualization of Tree Ring Density Variations. Proceedings of the International Conference Tree Rings and Environment. Tucson, AZ, USA, Radiocarbon, 1996, pp. 871–878.
Sharapov E., Brischke C., Militz H. Effect of Grain Direction on Drilling Resistance Measurements in Wood. International Journal of Architectural Heritage, 2021, vol. 15, iss. 2, pp. 250–258. https://doi.org/10.1080/15583058.2020.1766158
Sharapov E., Wang X., Smirnova E. Drill Bit Friction and its Effect on Resistance Drilling Measurements in Logs. Proceedings of the 20th International Nondestructive Testing and Evaluation of Wood Symposium, 12–15 September 2017, USDA Forest Service, Forest Products Laboratory, Madison, WI, 2017, pp. 405–415.
Sharapov E., Brischke C., Militz H., Smirnova E. Prediction of Modulus of Elasticity in Static Bending and Density of Wood at Different Moisture Contents and Feed Rates by Drilling Resistance Measurements. European Journal of Wood and Wood Products, 2019, vol. 77, pp. 833–842. https://doi.org/10.1007/s00107-019-01439-2
Schimleck L., Dahlen J., Apiolaza L.A., Downes G., Emms G., Evans R., Moore J., Pâques L., Bulcke J.V., Wang X. Non-destructive Evaluation Techniques and What They Tell Us About Wood Property Variation. Forests, 2019, vol. 10, iss. 728. 50 p. https://doi.org/10.3390/f10090728
Tannert T., Anthony R., Kasal B., Kloiber M., Piazza M., Riggio M., Rinn F., Widmann R., Yamaguchi N. In-situ Assessment of Structural Timber using Semi-destructive Techniques. Materials and Structures, 2014, vol. 47, pp. 767–785. https://doi.org/10.1617/s11527-013-0094-5
Wang S.Y., Chiu C.M., Lin C.J. Application of the Drilling Resistance Method for Annual Ring Characteristics: Evaluation of Taiwania (Taiwania cryptomeribides) Trees Grown with Different Thinning and Pruning Treatments. Journal of Wood Science, 2003, vol. 49, iss. 2, pp. 116–124. https://doi.org/10.1007/s100860300018
Wang S.Y., Lin C.J. Application of the Drill Resistance Method for Density Boundary Evaluation of Earlywood and Latewood of Taiwania (Taiwania cryptomerioides Hay.) Plantation Wood. Taiwan Journal of Forest Science, 2001, vol. 16, iss. 3, pp. 196–199.
