Force Analysis of a Single Grain Cutting Process in Wood Grinding Using Spherical Corundum
DOI:
https://doi.org/10.37482/0536-1036-2023-3-140-154Keywords:
force analysis, spherical corundum, abrasive wheels of spherical corundum, spherical corundum grain, grinding, wood grinding, grinding of wooden materialsAbstract
The productivity of the wood grinding process can be increased by using abrasive wheels with spherical corundum grains. They also expand the area of application of rigid abrasive instruments by reducing soiling and eliminating burns on the treated surface. The studies revealed several advantages of the abrasive wheels over sanding paper: very precise processing, achievement of the desired grade of the treated surface, high durability of the instrument, and low cost. A force analysis of a grinding surface with micro-cuttings made of spherical corundum grains was performed depending on the degree of its wear. The results revealed that chip removal by the spherical corundum grains was possible only under certain conditions when the cutting edges of the grains were exposed. Besides, the theoretical dependencies of forces in micro-cutting were obtained from every principal condition for the process of grinding wood and wooden materials: properties of the spheres, treatment modes, and material-related factors. The special properties were analyzed by the chip formation process and self-sharpening conditions of the spherical corundum wheels. The grain size had the greatest influence on the thickness of chips which were cut by one grain. The grain content and bonding, like other properties of the internal volumetric structure, had a less substantial impact. The abrasive tool characteristics must complement the processed material, such as grain size, hardness, and structure. On the other hand, spherical corundum has optimal physical and mechanical properties for grinding, particularly the thickness of the grain’s edges, which primarily determine the material’s tensile strength. The grinding depth and feed rate mostly define the parameters of the grinding performance of wood and wood-based materials. An increase in those leads to a rise in cutting forces, roughness of the ground surface, a reduction in the grinding length over the period of the wheel’s durability, and the grinding coefficient. If the grinding depth and feed rate are constant, the performance can be improved by increasing the cutting rate.
For citation: Sergeevichev A.V., Sokolova V.A., Mikhailova A.E., Ovcharova E.O., Voinash S.A. Force Analysis of a Single Grain Cutting Process in Wood Grinding Using Spherical Corundum. Lesnoy Zhurnal = Russian Forestry Journal, 2023, no. 3, pp. 140–154. (In Russ.). https://doi.org/10.37482/0536-1036-2023-3-140-154
Downloads
References
Виноградов В.Н., Сорокин Г.М., Колокольников М.Г. Абразивное изнашивание. М.: Машиностроение, 1990. 221 с. Vinogradov V.N., Sorokin G.M., Kolokolnikov M.G. Abrasive Wear. Moscow, 1990. 221 p. (In Russ.).
Каменев Б.Б., Сергеевичев А.В. Дереворежущие инструменты. СПб.: СПбГЛТУ, 2013. 332 с. Kamenev B.B., Sergeevichev A.V. Wood-Cutting Tools. Sankt Petersburg, SPbFTU Publ., 2013. 332 p. (In Russ.).
Кремень З.И., Буторин Г.И., Коломазин В.М. и др. Технология обработки абразивным и алмазным инструментом / под общ. ред. З.И. Кремня. Л.: Машиностроение, Ленингр. отд-ние, 1989. 206 с. Kremen Z.I., Butorin G.I., Kolomazin V.M. et al. Processing Technology with Abrasive and Diamond Tools. Leningrad, Mashinostroyeniye, Leningr. otd. Publ., 1989. 206 p. (In Russ.).
Любимов В.Г. Шлифование слоистых пластмасс кругами с абразивными зернами из стекла // Резание и инструмент: междунар. науч.-техн. сб. Харьков, 2002. Вып. 10. С. 73–77. Lyubimov V.G. Grinding of Laminated Plastics with Glass Abrasive Grains. Rezanie i instrument v texnologicheskix sistemax: mezhdunar. nauch.-texn. sb., 2002, no. 10, pp. 73–77. (In Russ.).
Маслов Е.Н. Теория шлифования материалов. М.: Машиностроение, 1974. 320 с. Maslov E.N. Theory of Grinding Materials. Moscow, Mashinostroenie Publ., 1974. 320 p. (In Russ.).
Островский В.И. Теоретические основы процесса шлифования. Л.: ЛГУ, 1981. 144 с. Ostrovsky V.I. Theoretical Bases of the Grinding Process. Leningrad, PLSU Publ., 1981. 144 p. (In Russ.).
Рыбин Б.М., Санаев В.Г., Кириллов Д.В. К вопросу выбора параметров шероховатости для оценки неровностей древесины // Вестн. МГУЛ – Лесной вестн. 2012. № 4. С. 68–71. Rybin B.M., Sanaev V.G., Kirillov D.V. To the Question of the Choice of Roughness Parameters for the Estimation of Woods Roughness. Lesnoj vestnik = Forestry Bulletin, 2012, no. 4, pp. 68–71. (In Russ.).
Санев В.И., Каменев Б.Б., Сергеевичев А.В. Резание древесины и древесных материалов. СПб.: Лань, 2018. 456 с. Sanev V.I., Kamenev B.B., Sergeevichev A.V. Cutting Wood and Wooden Materials. Sankt Petersburg, Lan’ Publ., 2018. 456 p. (In Russ.).
Demir H., Gullu A., Ciftci I., Seker U. An Investigation into the Influences of Grain Size and Grinding Parameters on Surface Roughness and Grinding Forces When Grinding. Strojniski vestnik = Journal of Mechanical Engineering, 2010, vol. 56, iss. 7/8, pp. 447–454.
Ichida Y. Formation Mechanism of Grain Cutting Edges in Micro Dressing of Polycrystalline CBN Grinding Wheels. Key Engineering Materials, 2012, vol. 523–524, pp. 137–142. https://doi.org/10.4028/www.scientific.net/KEM.523-524.137
Kivimaa E. Cutting Force in Woodworking. The Stat. Inst. for Tech. Res., Helsinki, 2000, no. 18, pp. 78–91.
Korolev A.V., Vasin A.N., Nazar’eva V.A., Reshetnikova O.P. Cutting Geometry of Abrasive Grains. Russian Engineering Research, 2014, vol. 34, no. 10, pp. 655–659. https://doi.org/10.3103/S1068798X14100086
Kryukov S.A., Kryukova A.S. Determining the Parameters of Grinding Wheels Working Surface Profile. Procedia Engineering, 2017, vol. 206, pp. 204–209. https://doi.org/10.1016/j.proeng.2017.10.461
Leonov S.L., Markov A.M., Belov A.B., Sczygol N. Generalized Mathematical Model Predicting the Mechanical Processing Topography. IOP Conference Series: Materials, Science and Engineering. Proceedings of the 7th International Scientific and Practical Conference on Innovations in Mechanical Engineering, ISPCIME 2015, September 23–25, 2015, Kemerovo, Russia. England, Bristol, IOP Publishing Ltd Publ., 2016, pp. 1–8. https://doi.org/10.1088/1757-899X/126/1/012009
Malkin S. Grinding Technology. Theory and Applications of Machining with Abrasives. New York, Industrial Press Publ., 2008. 372 р.
Marinescu I.D., Rowe W.B., Dimitrov B., Inasaki I. Tribology of Abrasive Machining Processes. Brent Beckley Inc. Cover Art Publ., 2004. 764 р. https://doi.org/10.1016/B978-081551490-9.50003-7
Narayanaperumal A., Lakshmanan V. Evaluation of the Working Surface of the Grinding Wheel Using Speckle Image Analysis. Proceedings of the ASME 2015 International Conference on Manufacturing Science and Engineering (MSEC2015), 2015. American Society of Mechanical Engineers Publ., 2015, Vol. 1: Processing, pp. 1–7. https://doi.org/10.1115/MSEC2015-9416
Nguyen A.T., Butler D.L. Correlation of Grinding Wheel Topography and Grinding Performance: A Study from a Viewpoint of Three-Dimensional Surface Characterization. Journal of Materials Processing Technology, 2008, vol. 208, iss. 1-3, pp. 14–23. https://doi.org/10.1016/j.jmatprotec.2007.12.128
NovoselovYu., Bratan S., Bogutsky V.Analysis of Relation Between Grinding Wheel Wear and Abrasive Grains Wear. Procedia Engineering, 2016, vol. 150, pp. 809–814. https://doi.org/10.1016/j.proeng.2016.07.116
Sergeevichev A., Belonogova N., Sergeevichev V., Byzov V., Mikhailova A. Investigation of the Influence of Certain Factors on the Quality of Processing During Hard Grinding. IOP Conference Series: Earth and Environmental Science. Proceedings of the 5th Pan-Russian Scientific Technical Conference on Forests of Russia: Policy, Industry, Science and Education. England, Bristol, IOP Publishing Ltd. Publ., 2020, vol. 574(1), pp. 1–9. https://doi.org/10.1088/1755-1315/574/1/012072
